ServicesMetal Roofing
Metal Roofing in Yulee
A metal roof costs more on day one and usually much less over the years you own it. We show you both numbers side by side, help you choose between standing seam and exposed-fastener panels, and install it with the details that keep it quiet and dry.
When a Metal Roof Makes Sense for Your Home
Metal is a good fit if you plan to stay in your home for a long while, you are tired of replacing shingles after every rough hurricane season, or you want a roof that handles heat and heavy rain with very little attention. It is not always the right answer, and we will tell you when a shingle roof replacement fits your budget and plans better.
We have been roofing since 1995, and the question we hear most is whether the extra cost pays off. Our answer starts with your roof: its pitch, its shape, what is under the old covering, and how long you expect to live there. Then we lay out the up-front price next to the expected lifespan and upkeep of each option, so the choice still feels right twenty years from now.
What Your Metal Roof Includes
Panel choice explained
Standing seam hides its fasteners under raised seams and needs the least upkeep. Exposed-fastener panels such as 5V crimp cost less to install but have screws and rubber washers that need checking as they age. We walk through both on your roof.
Old roof off, plywood checked
Once the old covering is stripped away, we go over the plywood sheet by sheet. Anything soft, spongy or rotted is swapped out before a single panel goes on, since metal holds only as well as the wood beneath it.
High-temperature underlayment
Metal panels get hot in a Florida summer. We use an underlayment rated for that heat so it does not soften or break down under the panels.
Coatings matched to salt air
Homes close to the coast see more salt in the air, which is hard on bare steel and cut edges. We match the panel metal, coating and fasteners to your exposure so corrosion is not a surprise later.
Trim, flashing and ridge vent
Eaves, rakes, valleys, pipe boots and the ridge are where metal roofs leak if they are rushed. Each gets trim and flashing made for the panel system, plus ventilation so your attic can breathe.
Permit and final cleanup
We pull the permit, schedule the inspection and run a magnet over your yard and driveway for screws and metal shavings before we leave.
Signs Metal Could Be Your Next Roof
- Your shingles are near the end
- Curling edges, bald spots and granules in the gutters mean a replacement is coming. That is the best time to compare metal, before you are forced into a quick decision.
- Storms keep costing you
- If wind keeps lifting tabs and you are on your second or third round of storm damage repair, a fastened metal system may cost less over time.
- Rust on an older metal roof
- Surface rust, loose screws or flattened washers on an existing metal roof can sometimes be fixed. When the panels themselves are thinning, it is time to replace them.
- You plan to stay for decades
- The longer you own your home, the more the long life of metal works in your favor.
- A hot upstairs
- Metal with a reflective finish and a good ridge vent can help an attic shed heat faster than dark shingles.
How a Metal Roof Job Runs
- 1
Free technician visit
We measure your roof, check the decking from the attic and note pitch, valleys and penetrations. You get a written estimate with each panel option and what it costs to own over time.
- 2
Ordering and permit
Metal panels are often cut to length for your roof, so we order once the measurements are final. We file the permit while the material is on its way.
- 3
Tear-off and dry-in
Old roofing comes off one section at a time and the deck is repaired and covered with underlayment the same day, so your home is not left open to an afternoon shower.
- 4
Panels, trim and inspection
Panels go on with the fastener pattern the system calls for, then trim, flashing and ridge cap. After the final inspection we walk the job with you and do the magnet sweep.
What Moves the Cost of a Metal Roof
A metal roof price depends far more on your roof than on a square-foot figure. We break the estimate into lines so you can see where the money goes, and we put the expected lifespan and upkeep beside it so you are comparing real value. Financing is available if it helps you choose the roof you actually want.
- Panel system
- Standing seam costs more than exposed-fastener panels but skips the screw and washer maintenance over the years.
- Roof shape and pitch
- Valleys, hips, dormers and steep slopes take more cutting, trim and labor than a simple gable.
- Decking condition
- We cannot see every soft spot until the old roof is off. Any wood replacement is priced per sheet on the estimate, so there is no guesswork.
- Metal and coating
- Aluminum or a heavier coating for salt exposure costs more up front and holds up better near the water.
Metal Roofing Questions We Hear
- Will rain sound loud on a metal roof?
- Not the way most people picture it. With solid plywood and a layer of underlayment between the panels and your ceiling, a downpour sounds close to rain on shingles. The drumming you may remember from a barn or shed comes from panels screwed straight to open purlins, and we never build a roof on your home that way.
- Does metal attract lightning?
- No. Lightning looks for the tallest path to the ground, like a tree or a utility pole, and the roofing material plays no part in where it lands. Metal also cannot catch fire, so in the rare event a bolt reaches your home, the roof itself will not burn.
- Can you put metal over my old shingles?
- Sometimes code allows it, but we usually recommend a tear-off. Removing the old layer lets us find and fix soft decking and gives the panels a flat, solid base. We will explain what we see on your roof before you decide.
- Will salt air rust it?
- Bare steel and cut edges can rust near the coast. That is why we match the metal, coating and fasteners to how close your home sits to salt water.
- How does a metal roof hold up in hurricane winds?
- Properly fastened panels and trim resist wind lift well, since there are no tabs for gusts to catch. The fastening pattern and edge details matter most, and we follow the system's requirements on both.
- Can I pay for it over time?
- Yes, financing is available. We can go over it during your free estimate so the monthly cost sits next to the long-term savings.
See What a Metal Roof Would Cost Over Time
We will look at your roof, price standing seam and exposed-fastener options, and show how each compares over the years you plan to stay. Homeowners in Yulee, Fernandina Beach and nearby get the same careful walk-through.